Brother Speedio machine monitoring
For CNC-C00 and CNC-D00 controls. What we read, how often, and what happens to your data when a connection drops.
Which Brother machines we connect
On a Brother machine, the control decides how it connects, not the Speedio model. We check it on every machine in the site survey.
CNC-D00
- How it connects
- OPC UA, built into the control
CNC-C00
- How it connects
- FTP, built into the control
B00, A00 and older
- How it connects
- Checked per machine in the site survey. If the control can't share data over the network, digital I/O gives running status and part count.
| Control | How it connects |
|---|---|
| CNC-D00 | OPC UA, built into the control |
| CNC-C00 | FTP, built into the control |
| B00, A00 and older | Checked per machine in the site survey. If the control can't share data over the network, digital I/O gives running status and part count. |
The model name usually tells you the control. Brother marks D00 machines with a “d” in the series code:
Xd1 or Xd2
- Examples
- S300Xd2, S500Xd2, S700Xd2, R450Xd2, R650Xd2, M200Xd1, M300Xd1, U500Xd2, H550Xd1, W1000Xd2
- Control
- CNC-D00
X2
- Examples
- S300X2, S500X2, S700X2, R450X2, R650X2
- Control
- CNC-C00
X1 and older
- Examples
- S300X1, S500X1, S700X1, R450X1, M140X1
- Control
- Check the control screen; confirmed in the site survey
| Model name ends in | Examples | Control |
|---|---|---|
| Xd1 or Xd2 | S300Xd2, S500Xd2, S700Xd2, R450Xd2, R650Xd2, M200Xd1, M300Xd1, U500Xd2, H550Xd1, W1000Xd2 | CNC-D00 |
| X2 | S300X2, S500X2, S700X2, R450X2, R650X2 | CNC-C00 |
| X1 and older | S300X1, S500X1, S700X1, R450X1, M140X1 | Check the control screen; confirmed in the site survey |
Brother Speedio series we monitor
Every Speedio is a compact BT30 machining centre, and every series connects the same way: through its control. These are Brother's current series.
S series
- What it is
- Drilling, tapping and milling centres; Brother's best-selling line
- Example models
- S300Xd2, S500Xd2, S700Xd2
R series
- What it is
- Two-pallet models: the next part is loaded while the current one is cut
- Example models
- R450Xd2, R650Xd2
M series
- What it is
- Mill-turn models: turning and milling in one setup
- Example models
- M200Xd1, M300Xd1
U series
- What it is
- Multi-face machining on a tilting rotary table
- Example models
- U500Xd2
H series
- What it is
- Compact horizontal machining centre
- Example models
- H550Xd1
W series
- What it is
- Wide table, the largest machining area in the BT30 class
- Example models
- W1000Xd2
| Series | What it is | Example models |
|---|---|---|
| S series | Drilling, tapping and milling centres; Brother's best-selling line | S300Xd2, S500Xd2, S700Xd2 |
| R series | Two-pallet models: the next part is loaded while the current one is cut | R450Xd2, R650Xd2 |
| M series | Mill-turn models: turning and milling in one setup | M200Xd1, M300Xd1 |
| U series | Multi-face machining on a tilting rotary table | U500Xd2 |
| H series | Compact horizontal machining centre | H550Xd1 |
| W series | Wide table, the largest machining area in the BT30 class | W1000Xd2 |
What we read from a Brother control
A D00 over OPC UA and a C00 over FTP give the same core data. All of it comes from the control itself, with no sensors added to the machine.
Machine state
- Examples
- Running, stopped, alarm, mode, emergency stop, doors
- What it gives you
- Live status and every downtime event, timed by the machine
Production
- Examples
- Part count, end of every cycle
- What it gives you
- Parts against target and actual cycle time per part
Program
- Examples
- Program running now; every program on the machine, with changes kept
- What it gives you
- Every stop and every part tied to the job that was running
Alarms
- Examples
- Alarm number and message, with start and end time
- What it gives you
- Downtime that names its own cause
Cutting
- Examples
- Feedrate, spindle speed, feed and spindle override, tool in use
- What it gives you
- Overrides left turned down and slow running, made visible
Tool life
- Examples
- The tool wear counters the control already keeps
- What it gives you
- Remaining life per tool, before it breaks
| Data | Examples | What it gives you |
|---|---|---|
| Machine state | Running, stopped, alarm, mode, emergency stop, doors | Live status and every downtime event, timed by the machine |
| Production | Part count, end of every cycle | Parts against target and actual cycle time per part |
| Program | Program running now; every program on the machine, with changes kept | Every stop and every part tied to the job that was running |
| Alarms | Alarm number and message, with start and end time | Downtime that names its own cause |
| Cutting | Feedrate, spindle speed, feed and spindle override, tool in use | Overrides left turned down and slow running, made visible |
| Tool life | The tool wear counters the control already keeps | Remaining life per tool, before it breaks |
Brother OPC UA and FTP: how each control connects
CNC-D00OPC UA
OPC UAis the open standard industrial machines use to share data with software, with security built in. ThingConnect uses it only to read the machine's data.
The D00 control has an OPC UA server built in. Your maintenance engineer switches it on in the control's network settings, and ThingConnect reads the machine live from then on. No add-on, no licence, no PC at the machine.
CNC-C00FTP
FTP is a simple, long-standing way to fetch files from a device over the network. Most CNC controls use it to send and receive programs.
The C00 control has no OPC UA, but it keeps its status, part counter, alarms and logs as files on its own FTP server. ThingConnect reads those files live, together with the control's built-in web page, so a C00 shows the same status, parts, program and alarms as a D00. The control's own logs also record what happened while nobody was looking.
Not every Brother has OPC UA.A page that says “Brother connects over OPC UA” leaves out every C00 machine. We connect both, so a plant with older and newer Speedios sees all of them on one dashboard.
How the data gets from the machine to your screen
Your plant
CNC-D00
OPC UA
CNC-C00
FTP
ThingConnect gateway
reads every machine, holds data if internet drops
- ThingConnect cloud
- Live dashboardOEE reportsDowntime reports
- 1Each Brother control is connected to the plant network with an Ethernet cable.
- 2The ThingConnect gateway in your plant reads every machine: D00 over OPC UA, C00 over FTP.
- 3The gateway sends the data to the ThingConnect cloud over one secure outbound connection.
- 4You see live status, OEE and downtime on any screen, and reports by shift and day.
What you do with the data
Live machine status
Every Brother machine running, idle, in alarm or offline, on one screen and on the shop-floor TV.
OEE
Availability, performance and quality per machine and shift, calculated from the control's own data.
Production against target
Parts made against plan, hour by hour, from the machine's part counter.
Downtime and reasons
Every stop recorded with its start and end time. Alarms name the cause; operators add the rest.
Cycle time
Actual cycle time per part and per program, so slow running shows up the same shift.
Machine utilization
How many hours each machine actually cut, against the hours it was available.
If the network drops, the lost time comes back
Networks drop and gateways get restarted. Most monitoring systems show that time as blank, or worse, as idle. A Brother D00 keeps its own record of when it ran and when it stopped. When the connection returns, ThingConnect reads that record back and fills the gap.
Running and stopped time
- What ThingConnect does
- Filled in from the machine's own record
Parts made during the gap
- What ThingConnect does
- Filled in only when the machine's part counter and its own list of finished cycles agree. If they don't, the gap stays visible. We never guess.
Time the machine was switched off
- What ThingConnect does
- Stays empty
| After the connection returns | What ThingConnect does |
|---|---|
| Running and stopped time | Filled in from the machine's own record |
| Parts made during the gap | Filled in only when the machine's part counter and its own list of finished cycles agree. If they don't, the gap stays visible. We never guess. |
| Time the machine was switched off | Stays empty |
Checked on a real outage.After a 68-minute network drop, the running time we rebuilt was within 2% of what the machine itself recorded. The parts for that hour were not filled in, because the counter and the cycle list didn't match.
Setup: what your maintenance team does
1. Network
- CNC-D00
- Connect the control to the plant network and give it a fixed IP address
- CNC-C00
- Connect the control to the plant network and give it a fixed IP address
2. Switch on data sharing
- CNC-D00
- Set the OPC UA server to Valid in the control's Ethernet / FTP settings
- CNC-C00
- Set up an FTP user on the control
3. Hand over
- CNC-D00
- Our team connects the gateway and checks the live data against the control's screen
- CNC-C00
- Our team connects the gateway and checks the live data against the control's screen
| Step | CNC-D00 | CNC-C00 |
|---|---|---|
| 1. Network | Connect the control to the plant network and give it a fixed IP address | Connect the control to the plant network and give it a fixed IP address |
| 2. Switch on data sharing | Set the OPC UA server to Valid in the control's Ethernet / FTP settings | Set up an FTP user on the control |
| 3. Hand over | Our team connects the gateway and checks the live data against the control's screen | Our team connects the gateway and checks the live data against the control's screen |
Nothing is installed on the machine, and no machine is stopped for the setup.
Common Brother problems, and what we do about them
OPC UA stops working after an FTP password was set on a D00 (error: “Endpoint does not support the user identity type provided”)
- What's happening
- Once a password is set, the control only accepts OPC UA connections that log in.
- What we do
- We log in with the same user name and password as FTP.
The part count suddenly jumps or drops during a shift
- What's happening
- An operator set or reset the counter on the control.
- What we do
- A drop is treated as a reset, never as negative production. A big jump is treated as a manual change.
The part count is lower than the number of cycles run
- What's happening
- The counter only counts cycles whose program tells it to count.
- What we do
- We check the counter against the machine's list of finished cycles.
“Error occurred” on the control after every part
- What's happening
- Almost always the door-open message, not a fault.
- What we do
- Shown as idle, not as a red alarm.
| What you see | What's happening | What we do |
|---|---|---|
| OPC UA stops working after an FTP password was set on a D00 (error: “Endpoint does not support the user identity type provided”) | Once a password is set, the control only accepts OPC UA connections that log in. | We log in with the same user name and password as FTP. |
| The part count suddenly jumps or drops during a shift | An operator set or reset the counter on the control. | A drop is treated as a reset, never as negative production. A big jump is treated as a manual change. |
| The part count is lower than the number of cycles run | The counter only counts cycles whose program tells it to count. | We check the counter against the machine's list of finished cycles. |
| “Error occurred” on the control after every part | Almost always the door-open message, not a fault. | Shown as idle, not as a red alarm. |
A mixed fleet is normal. Brother machines usually sit next to other brands. A FANUC on FOCAS, a Brother on OPC UA or FTP, and an older machine on digital I/O all land on the same dashboard.
Frequently asked questions
No. Only machines with the CNC-D00 control have an OPC UA server built in. Machines with the CNC-C00 control don't, and we connect those over FTP instead. Both give you live status, part count, program and alarms on the same dashboard.
Give the control a fixed IP address on your network, then set the OPC UA server to Valid in the control's Ethernet / FTP settings and save. Our team walks your maintenance engineer through it during installation.
CNC-D00 and CNC-C00, both running in production today. Older A00 and B00 controls are checked machine by machine in the site survey. Where a control can't share data over the network, a digital I/O connection still gives running status and part count.
On a D00, the machine keeps its own record of when it ran and stopped. When the connection returns, ThingConnect reads that record and fills the gap. Parts are filled in only when the machine's counter and its cycle record agree; otherwise the gap stays visible.
No. Monitoring doesn't change programs, settings or how the machine runs. ThingConnect reads the machine's data, and the machine itself never connects to the internet.
See it live
